• Welcome to the CaliforniaSpecial.com forums! - You are currently viewing the forums as a GUEST. To take advantage of all our site features, please take a moment to join our community! It's fast, simple and absolutely free.

    If you have problems registering or can't log into your account, please contact Admin.

    Please Note: If you are an existing member and your password no longer works, click here to reset it.

Search results

  1. Russ

    Curious--how much less is a CS worth w/o...

    Question: Where is the serial number stamping on the 200 ci six, and where is it located on the 390ci?? Lots of discussion on the 289/302. I checked two other 1968 289 engine blocks I have, and guess what........no stamped VIN numbers on that machined surface behind the intake maniflod. These...
  2. Russ

    problem with my fan

    Too bad about the fan shroud, as a replacement is around $100. You can get some plastic epoxy and glue it back together. I did that on my GT, and it has been holding for the past year. About the fan, there are many different 1968 fans, and some have a larger diameter. My car (289 cu in with...
  3. Russ

    stupid move

    If you want to cover the door edge, I would suggest purchasing accessory chrome door edge guards. This will cover any paint chips and was an original accessory from Ford. Just a thought, Russ
  4. Russ

    Curious--how much less is a CS worth w/o...

    Cory, I totally agree with you. Russ
  5. Russ

    Curious--how much less is a CS worth w/o...

    I would be careful about determining value of a car that has had its engine swapped. It is a rare find indeed, for a 35+ year-old car to have its original engine/drive train. I also think it must be clear as to what constitutes a "numbers-matching" car. It is clear that Ford had casting...
  6. Russ

    Argent taillight panel

    People paint the rear panel silver to look like a Shelby. The GT/CS came with a panel that was the color of the car. I know of no exceptions. Russ
  7. Russ

    Deluxe Seat Belts

    The length of the shoulder belt is shorter than the lap belt. The receiver buckle is the same on both belts. The lap belt is 41" and the shoulder belt is 27" long. You could use a rear belt, as it is 26" long. Russ
  8. Russ

    Correct Dash Bezel

    The dash option, other than the "camera case" finish is the wood grain "deluxe interior trim" option. This includes a roof "console", upgraded side panels, special chrome trim on the seats and the wood grained dash (including bezal) and steering wheel. This option is identifed on the warranty...
  9. Russ

    Deluxe Seat Belts

    Interestingly enough, the shoulder harness system is not considered part of the deluxe belt option. What identifies the deluxe option is the plastic chrome trim on the safety belt latch. I have the standard belts, including shoulder belts, in my GT/CS, and the belt latch is entirely black...
  10. Russ

    paint colour

    If you would like a perfect color match and an easy application when you repaint a GT/CS grill or its surrounding grill trim, use Seymore "original" Cast Blast paint. The color is called "Cast Iron Gray" and part number is #16-148. This paint comes in a 12 oz. spray can and is easy to purchase...
  11. Russ

    Color of engine compartment.

    On the San Jose cars that I own, the underside of the transmission hump is red oxide. The cars were dipped in red oxide primer and numerous drips can bee seen on the floor pans as a result. The cars were then painted the exterior color, and overspray went into the engine compartment and...
  12. Russ

    Dual GT Quad Tip Specs

    I'm glad it worked out well for both of you!! I think the dual quad tips look great on a '68 Mustang, and I know that your cars will really "show" well with this exhaust. Russ
  13. Russ

    My Lucas lights and pedestal

    I'm with you, I would not change it either. The dimensions for the holes for the tubular mounts are found in Paul's book. I don't know if you would have to change your mounting holes, but my GT/CS, which came with the square mounts also, was drilled using the same specifications as the...
  14. Russ

    Dual GT Quad Tip Specs

    I have an original 1968 GT with the original exhaust system. I took each measurement from the top of the dual tips on the driver side. The measurement from the bottom edge of the bumper to the top of the dual tip is 4". The dual tip sticks out 1 1/2" from the "cut out" in the valance. This...
  15. Russ

    My Lucas lights and pedestal

    When I purchased my GT/CS, it had the square Lucas mounts also. My car was built on February 14, BUT was not sold from the California dealer until May 15th. Remember, in California, these cars had to be retrofitted with the Lucas lights, and this occurred around the end of April, 1968. It...
  16. Russ

    They're Still Out There

    UPDATE: Well, I got the Marti Report on 8R01J156978, and it is an Acapulco blue GT/CS that came with a four speed, adjustable mirror, front seat headrests, PS, AM Radio, F70X14 wide-oval WSW tires and deluxe wheel covers. It was ordered by the Seattle district. Interestingly enough, the car...
  17. Russ

    Concours Restoration Books/Marks

    Paul, I agree with you that you need to find every bit of information you can to "correctly" restore your GT/CS. The more research and documentation you can find the better. The assembly manuals are but one source of information. I also agree that one has to determine what the car will be...
  18. Russ

    Long Time GT/CS owner with ?

    One thing you might need an answer to is which type of rear side marker is on the car. It states the car is an early car, so I'm assuming it has the indented type of fender. I'm not sure, but I think the placement of the "California Special" name may be a little bit different, based upon the...
  19. Russ

    Marchal Bracket Rivets

    The item is called a "rivet set" and they are difficult to find because few people connect items together usng rivets. I also restore Model T Fords and you have to have these tools to complete resotrations. Rivet sets for riveted brake lining works on a tubular rivet as it "splays" the tubular...
  20. Russ

    Marchal Bracket Rivets

    When I started the restoration of my GT/CS, the very first thing I started with was the restoration of the grill. I found a company in Plymouth, MA that had aluminum "tinner's rivets" for the grill, and all I could purchase was a 1 lb. box of these rivets. These rivets match the specs found in...
Top