-- Message Boards -- 1968 California Special Limited Edition Ford Mustang GT/CS
D I S C U S S I O N . F O R U M
1968 GT/CS & HCS
2007+ GT/CS
1966-1967 HCS

Old 05/20/2013, 11:32 AM   #1

Joined: Oct 07
Posts: 516

Front Tire

Could some help and tell me why the front tire is rubbing the front fender not all the time but it is cutting in to the tire could it be ball joints or tie rods need help thanks Tom FRom Wisconsin
green56 is offline  
Old 05/20/2013, 03:01 PM   #2
My Car Details
franklinair's Avatar

Location: Franklin, NC
Joined: Mar 07
Posts: 4,564

My Garage
What size wheel & tires are you using?

franklinair is offline  
Old 05/21/2013, 08:53 AM   #3

Joined: Oct 07
Posts: 516

Tire Rub bing

R2.25/R60/15 all the way around that is the only one that rubs the tire is a Goodrich Radial R/T
green56 is offline  
Old 05/26/2013, 10:42 AM   #4
robert campbell
My Car Details

Location: Bremerton Washington
Joined: Apr 07
Posts: 4,273

My Garage
I doubt that a worn front end would cause this. A P225 60R 15 is a fairly large tire, but many people have them on there cars. Are you using a stock Ford rim on your car? If not the offset of the wheel could be the problem.

The other factor is how high does you car sit on a level surface. If your car is lowered, you will have more chance of tire rubbing.

The below two links to our site are chock full of information. Look them over

robert campbell is offline  
Old 05/27/2013, 07:17 AM   #5

Joined: Oct 07
Posts: 516

I have the Magnum 500 rims I put new leaf springs in back did not lower car I have a Alinement place I will be going to on WENSDAY this week have a set of front springs I will take them along just in case and the rubbing is only on the Passanger side
green56 is offline  
Old 06/03/2013, 04:42 AM   #6

Joined: Oct 07
Posts: 516

front end

Have the68 GT/CS front end fixed they replaced the lower control arm abd ball joint it run nice and drives nice now I have to replace the PS Control Valve then it should drive and ride good Tom From Wisconsin
green56 is offline Forums > GT/CS and HCS Forums > Restoration Reference Archives > Wheels & Tires

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
1968 - Does anyone have any suggestions for front end alignment specs for a big block? GT/CS S Code GT/CS and HCS Discussions 4 07/26/2010 07:43 AM
1968 - Rebuild Front End 68P51 GT/CS and HCS Discussions 5 09/07/2009 01:35 PM
question about lifting front end dragonkff GT/CS and HCS Discussions 5 05/22/2008 09:37 PM
HVBoM Report on a Shelby GT bztz4m GT/CS and HCS Discussions 0 03/05/2007 10:08 AM
HVBoM Report from the Ford parts dept. bztz4m GT/CS and HCS Discussions 6 03/02/2007 08:24 PM

All times are GMT -7. The time now is 06:07 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2022, vBulletin Solutions Inc.

This site created, owned and maintained by Jon Hanna - Copyright 1996-2011
All rights reserved. is not affiliated with Ford Motor Company

ShowCase vBulletin Plugins by Drive Thru Online, Inc.