SOLD NOS 1968 California Special script badges

[mwilson7]

Unfortunately the only hardware I had was in the boxes with the badges

 

[CaliStang68]

Unfortunately the only hardware I had was in the boxes with the badges

Thank you Sir. However, should you find any, you know where to find me.
Rick

 

[Mosesatm]

Have you tried NPD?

 

[CaliStang68]

Have you tried NPD?

I was looking for the barrell nuts that attach to these emblems. It appeared he had some, but it was a mistake. All good I'll find some eventually.

 

[Jschoony]

Thank you Sir. However, should you find any, you know where to find me.
Rick

Is this what you are looking for?

1968 Mustang California Special Script Hardware Kit

store.cobranda.com

 

[Jschoony]

I was looking for the barrell nuts that attach to these emblems. It appeared he had some, but it was a mistake. All good I'll find some eventually.

Or if you prefer NPD theses are the same. Also they are just a tinnerman nut and a lot of Ace hardwares will have them.

NUT KIT, STAMPED SHEET METAL - #13A355-1K - National Parts Depot

Buy part #13A355-1K NUT KIT, STAMPED SHEET METAL for your classic vehicle from National Parts Depot. Free shipping on orders over $300, fast delivery & everyday low pricing! Order now!

www.npdlink.com

Sent from my iPhone using Tapatalk

 

[CaliStang68]

Wow thanks Jschoony! I always thought they were barrel nuts.

 

[Jschoony]

Wow thanks Jschoony! I always thought they were barrel nuts.

Yeah I know some of the Shelby emblems use this same flat tinnerman nut. The old NOS emblems the flat nuts are black the new ones look almost zinc?

 

[Ricky Knapik]

Darn I missed this. Do you at least have any of the attaching hardware left?

If you're talking about the retaining clips, I can probably help you.

 

[CaliStang68]

Hello,
Yes, that's great! how so?

 

[Ricky Knapik]

Hello,
Yes, that's great! how so?

Well, after I said that, I saw the link above. That's all you need.

 

[CaliStang68]

Thanks. I just looked yesterday as well, the last time I looked they were out of stock.

 

[Ricky Knapik]

Thanks. I just looked yesterday as well, the last time I looked they were out of stock.

I'll check, I think I have some. You need for both sides?

 

[CaliStang68]

Thanks yes. Much appreciated. NPD and cobranda actually don't specify they are for CS script. Let me know how much you want for them if you have some or PM me.
Thanks
Rick

 

[franklinair]

I just checked NPD P/N 13A355-1K- they indicate they DO have stock.

Neil

 

[pfinleyz]

I looked everywhere, some sites will say they have it but then when you order it , it says not available. Branda was out as of 3 or 4 weeks ago, my understanding is only Scott Drake was making them and they have discontinued them

 

[pfinleyz]

My husband and I both swear we had the emblems on the car, in the 15 years of it sitting and parts here and there well, these aren't the only parts we can't find. If I do find them I'll post them for sale

 

[Jschoony]

I looked everywhere, some sites will say they have it but then when you order it , it says not available. Branda was out as of 3 or 4 weeks ago, my understanding is only Scott Drake was making them and they have discontinued them

The Branda kit was made by Pony

 

[CougarCJ]

Those fasteners are also called 'ribbon nuts'. They come in various sizes. I will see if I can get a measurement on my NOS set.

 

[Ricky Knapik]

Ok everyone. I've been following the discussion on the "flat nuts" used to install the badges. I needed them a few years ago. Based on my research, I came up with something pretty damn close. I will not say they are concourse, but I would guess it would take a digital micrometer to tell the difference. I bought these at Fastenal that happens to be across the street from my work. 100 for about $9.00. "Auveco 2100" seems to be readily available on the internet. Hope that helps everyone!